MECHANIC MOTOR VEHICLE
(THEORY)
SEMESTER – III
JULY 2018
The clutch cover is bolted to ….a. Fly wheel
b. Car frame
c. Engine block d. Clutch disc Answer: a. Fly wheel
The following provides a smooth means of
disengagement and engagement between the
engine and the remainder of transmission system-
a. Clutch
b. Gearbox
c. Propeller shaft
d. Differential
Answer: a. Clutch
The torque which a clutch can transmit, depends upon the-
a. Coefficient of friction
b. Spring force
c. Contact surfaces
d. All of these
Answer: d. All of these
Mechanical transmission can be of following class(es) ….
a. Clutch, gearbox and live axle transmission
b. Clutch, gearbox and dead axle transmission
c. Clutch, gearbox and axle less transmission .
d. All of the above
Answer: d. All of the above
Which type of gear box is used in automobiles?
a. Sliding mesh gear box
b. Differential gear box
c. Synchromesh g
d. All of these
Answer: d. All of these
Four-wheel drive vehicles have differential at …..
a. Front wheels
b. Rear wheels
c. Both the front and rear wheels
d. Any of the front or rear wheels
Answer: c. Both the front and rear wheels
The differential unit consists …….
a. One bevel pinion
b. Two bevel pinion
c. Three bevel pinion
d. Four bevel pinion
Answer: b. Two bevel pinion
Which of the following is a higher pair?
a. Turning pair
b. Screw pair
c. Belt and pulley
d. None of these
Answer: c. Belt and pulley
For a simple gear train, velocity ratio is the ratio of ……………
a. Speed of driving shaft and speed of driven shaft
b. Speed of driven shaft and speed of driving shaft
c. Speed of driven shaft and (speed of driving shaft + speed of idler gears)
d. Speed of driving shaft and (speed of driven shaft + speed of idler gears)
Answer: b. Speed of driven shaft and speed of driving shaft
In a simple gear train, if the number of idle gears is odd, then the motion of driven gear will-
a. Be same as that of driving gear
b. Be opposite as that of driving gear
c. Depend upon the number of teeth on the driving gear
d. None of the mentioned
Answer: a. Be same as that of driving gear
To connect two parallel and coplanar shafts the following type of gearing is used-
a. Spur gear
b. Bevel gear
c. Spiral gear
d. None of these
Answer: a. Spur gear
In which of the following type of gear train the first gear and the last gear are co-axial.
a. Simple gear train
b. Compound gear train
c. Reverted gear train
d. None of these
Answer: c. Reverted gear train
Transfer case is located next to the gearbox in …..
a. Front wheel drive
b. Rear wheel drive
c. Four wheel drive
d. All of these
Answer: c. Four wheel drive
Which of the following is not an example of recuperations' type heat exchanger?
a. Automobile radiators
b. Condensers
c. Chemical factories
d. Oil heaters for an aero
Answer: c. Chemical factories
In Disc clutch, the clutch disc acts as a ……
a. Driving member
b. Driven member
c. Neutral member
d. Any of these
Answer: b. Driven member
The following components forms valve operating mechanism except …..
a. Push rod . .
b. Rocker arm
c. Valve seat
d. Fork
Answer: d. Fork
Machine member used to connect engine shaft to gear box is cal led-
a. Differential
b. Clutch
c. Flywheel
d. Propeller shaft
Answer: b. Clutch
Which type of clutch does not require clutch pedal?
a. Single plate
b. .Multi plate
c. Centrifugal
d. Cone
Answer: c. Centrifugal
The valve is opened as the cam lobe on the cam raises the …..
a. Bearing
c. Valve lifter
b. Piston
d. Valve seat
Answer: c. Valve lifter
The size of the engine intake valve is ……………
a. Same as that of exhaust valve
b. Smaller than that of exhaust valve ,
c. Larger than that of exhaust valve
d. Does not depend upon the size of exhaust valve
Answer: b. Smaller than that of exhaust valve
The purpose of valve clearance is to ………..
a. Allow the valve to expand
b. Allow the sliding of valve in the guide
c. Ensure that the valve closes fully
d. Ensure that the crankshaft is free to rotate
Answer: c. Ensure that the valve closes fully
A relief valve is fitted to the main oil gallery of an engine.
The purpose of this valve is to-
a. Limit the maximum oil pressure
b. Open when the oil is hot
c. Maintain the supply if the gallery becomes blocked
d. Stop the oil flow to the bearings
Answer: a. Limit the maximum oil pressure
Which vehicle is generally provided with four wheel drive?
a. Ambassador car
b. Standard wagon
c. Matador
d. Jeep
Answer: d. Jeep
Leaf springs absorb shocks by ………..
a. Bending
b. Twisting
c. Compression
d. Tension
Answer: a. Bending
The following is (are) the independent suspension system(s) …..
a. Wishbone Arm system
b. Trailing Link system
c. Sliding Pillar system
d. All of these
Answer: d. All of these
The Ackermann steering iayout ……..
a. Makes for safer driving
b. Enables the driver to feel ahead position
c. Reduces load on the kingpins and stub axles
d. None of the above
Answer: a. Makes for safer driving
In disc brake, the disc is attached to the ………
a. Wheel
b. Axle
c. Suspension system
d. None of these
Answer: b. Axle
The function of master cylinder in hydraulic brakes is to ……….
a. Builds up hydraulic pressure to operate the brakes
b. Maintains constant volume of fluid in the system
c. Serves as a pump to force air out of the hydraulic system
d. All of the above
Answer: d. All of the above
The following factor(s) contribute to the effectiveness of the brakes ………..
a. Area of brake linings
b. Radius of car wheel
c. Amount of pressure applied to shoe brakes
d. All of the above
Answer: d. All of the above
The process of removing air from the brake system is known as …..
a. Bleeding
b. Self-energizing .
c. Servo action
d. Energization
Answer: a. Bleeding
When brakes are applied on a moving vehicle;
the kinetic energy is converted to ……..
a. Mechanical energy
b. Heat energy
c. Electrical energy
d. Potential energy
Answer: b. Heat energy
The force required to stop a vehicle is dependent on ……
a. The weight of vehicle
b. The deceleration rate
c. Both a and b
d. None of these
Answer: c. Both a and b
Coil springs absorb shocks by……….
a. Bending
b. Twisting
c. Compression
d. Tension
Answer: c. Compression
The following is a type of leaf springs ……….
a. Three Quarter elliptic
b. Semi elliptic
c. Quarter elliptic
d. All of these
Answer: d. All of these
The material used for making torsion bar is ………
a. Steel
b. Cast iron
c. High carbon steel
d. All of these
Answer: a. Steel
Spring shackles are used to join ……….
a. Chassis frame and spring
c. Chassis frame and axle
b. Spring and Axle
d. All of these
Answer: a. Chassis frame and spring
Cam actuated double acting hydraulic shock absorber contains ……..
a. No piston
b. Single piston
c. Double pistons
d. Three pistons
Answer: c. Double pistons
The main reasons for crankshaft wear are ………….
a. Different loads at some points of rotation
b. Centrifugal forces due to crankshaft rotation
c. Misalignment in connecting rod
d. All of the mentioned
Answer: d. All of the mentioned
The main causes of crankshaft vibration are ………
a. Variation in torque
b. Cyclic variation of gas and combustion products
c .Unbalanced weight of parts
d. All of the mentioned
Answer: . d. All of the mentioned
In the cam, the distance between the base circle and the nose is called ……..
a. Lift
b. Lobe
c. Flank
d. Pitch
Answer: a. Lift
The function of anti-lock brake system (ABS) is that is ………….
a. Reduces the stopping distance .
b. Minimizes the brake fade
c. Maintains directional control during braking by preventing the wheels from locking
d. Prevents nose dives during braking and thereby postpones locking of the wheels
Answer: c
In a four wheel drive (4 WD), the numbers of gear boxes are ……………
a. 1
b. 2
c. 3
d. 4
Answer: b. 2
In the steering gear, a gear sector or toothed roller is meshed with a …….
a. Ball bearing
b. Roller bearing
c. Worm
d. Steering wheel
Answer: c. Worm
The only service that a steering linkage normally requires is ……….
a. Tie-rod adjustment
b. Lubrication
c. Ball-joint replacement
d. None of the mentioned
Answer: a. Tie-rod adjustment
Too much toe-in will be noticed by ……….
a. Excessive tyre wear because of taking
b. Steering wander
c. Feathering of tyres
d. Light steering
Answer: a. Excessive tyre wear because of taking
The most widely used-brakes are operated ………
a. Electrically
b. Hydraulically
c. By air pressure
d. By vaccum
Answer: b. Hydraulically
Of the four tyres on a car, the one that wears most is ……
a. Right front tyre
b. Right rear tyre
c. Left front tyre
d. Left rear tyre
Answer: b. Right rear tyre
Weight can be attached to wheel rim to correct ……..
a. Wheel alignment
b. Wheel balance
c. Wheel run out
d. All of these
Answer: b. Wheel balance
Steering gear …….
a. Rack and pinion type
b. Worm and roller type
c. Recirculating ball type
d. Any of these
Answer: d. Any of these
Wheel base of a vehicle is the ……
a. Distance between front and rear axles
c. Extreme length of the vehicle
b. Distance between the front tyres
d. Width of tyres
Answer: a. Distance between front and rear axles
No comments:
Post a Comment