FITTER THEORY MCQ
1) An accident is ..............
a. Unplanned event
b.Undesirable event
c. Non-controlled event
d.All of these
Answer:d.All of these
2) An oily floor should be cleaned by
a. Cotton waste
b. Putting water
c. Putting saw dust
d. Spraying carbon dioxide
Answer:d. Spraying carbon dioxide
3) Which tool is used to cut excessive thick sheet?
a) Snip
b) Shear
c) Hem
d) None of these
Answer:b) Shear
4) Zinc coated sheet is krrown as
a) Tin coated sheet
b) Galvanized iron sheet
c) Stainless steel
d) Lead sheet
Answer:b) Galvanized iron sheet
5) What is the full form of C'fC?
a) Carbon Tetra Chloride
b) Carbon Tin Chloride
c) Calcium Tetra Chloride
d) None of these
Answer:a) Carbon Tetra Chloride
6) Which of the following is not related to marking media?
a) Layout Die
b) Prussian Blue
c) Surface plate
d) None of these
Answer:c) Surface plate
7) There is negative error 0.03 mm in any micrometer. If the micrometer gives the reading
of 40.53 mm, then what will be the accurate readings?
a) 40.50 Millimeter
b) -10.56 Millimeter
c.140.83 Millimeter
d) 40.23Millimeter
8) While marking from Vernier height gauge, it should be moved by holding its base in such
a way that: -
a) Main scale should bend
b) Zero error or main scale should check
c) Main scale should not bend
d) Base of the offset scriber should be parallel to the surface prate
Answer:c) Main scale should not bend
9) Maximum keys are rnade up of: -
a) High speed steel
b) Mild steel
c) Cast iron
d) Pig iron
Answer:b) Mild steel
10) Power hammer mostly operated by which of the following: -
a) By hand
b) By electricity
c) Both (a) & (b)
d) None of these
Answer:b) By electricity
11) Length of snap head rivet is given by the formula: -
a)L=2d
b) L= T + 0.6d
c) L= T + 1.5d
d) None of these
Answer:c) L= T + 1.5d
12) The filing of wood. rubber etc. is done by which of the following file?
a) curved file
b) Single cur file
c) Double cut file
d) Rasp cut file
Answer:d) Rasp cut file
13) What happens by increasing the amount of carbon in steel?
a) Hardness increases
b)Rigidity increases
c) Rigidity decreases
d) Ductility increases
Answer:a) Hardness increases
14) Why soft jaws are used in vice?
a)To protect the finished surface
b) To hold the job more strongly
c) To protect the jaws of the vice
d) To protect the file
Answer:a)To protect the finished surface
15) Where the hatchet stake is used?
a) For riveting
b) Iior making flange
c) For folding sheets
d) None of these
Answer:c) For folding sheets
16) Pinning of file is removed by: -
a) File card
b) file handle
c) Wire brush
d) Dresser
Answer:a) File card
a. Unplanned event
b.Undesirable event
c. Non-controlled event
d.All of these
Answer:d.All of these
2) An oily floor should be cleaned by
a. Cotton waste
b. Putting water
c. Putting saw dust
d. Spraying carbon dioxide
Answer:d. Spraying carbon dioxide
3) Which tool is used to cut excessive thick sheet?
a) Snip
b) Shear
c) Hem
d) None of these
Answer:b) Shear
4) Zinc coated sheet is krrown as
a) Tin coated sheet
b) Galvanized iron sheet
c) Stainless steel
d) Lead sheet
Answer:b) Galvanized iron sheet
5) What is the full form of C'fC?
a) Carbon Tetra Chloride
b) Carbon Tin Chloride
c) Calcium Tetra Chloride
d) None of these
Answer:a) Carbon Tetra Chloride
6) Which of the following is not related to marking media?
a) Layout Die
b) Prussian Blue
c) Surface plate
d) None of these
Answer:c) Surface plate
7) There is negative error 0.03 mm in any micrometer. If the micrometer gives the reading
of 40.53 mm, then what will be the accurate readings?
a) 40.50 Millimeter
b) -10.56 Millimeter
c.140.83 Millimeter
d) 40.23Millimeter
8) While marking from Vernier height gauge, it should be moved by holding its base in such
a way that: -
a) Main scale should bend
b) Zero error or main scale should check
c) Main scale should not bend
d) Base of the offset scriber should be parallel to the surface prate
Answer:c) Main scale should not bend
9) Maximum keys are rnade up of: -
a) High speed steel
b) Mild steel
c) Cast iron
d) Pig iron
Answer:b) Mild steel
10) Power hammer mostly operated by which of the following: -
a) By hand
b) By electricity
c) Both (a) & (b)
d) None of these
Answer:b) By electricity
11) Length of snap head rivet is given by the formula: -
a)L=2d
b) L= T + 0.6d
c) L= T + 1.5d
d) None of these
Answer:c) L= T + 1.5d
12) The filing of wood. rubber etc. is done by which of the following file?
a) curved file
b) Single cur file
c) Double cut file
d) Rasp cut file
Answer:d) Rasp cut file
13) What happens by increasing the amount of carbon in steel?
a) Hardness increases
b)Rigidity increases
c) Rigidity decreases
d) Ductility increases
Answer:a) Hardness increases
14) Why soft jaws are used in vice?
a)To protect the finished surface
b) To hold the job more strongly
c) To protect the jaws of the vice
d) To protect the file
Answer:a)To protect the finished surface
15) Where the hatchet stake is used?
a) For riveting
b) Iior making flange
c) For folding sheets
d) None of these
Answer:c) For folding sheets
16) Pinning of file is removed by: -
a) File card
b) file handle
c) Wire brush
d) Dresser
Answer:a) File card
No comments:
Post a Comment