Jan2018 TURNER THEORY
SEMESTER-III
The angle on which the strength of tool depend is-
a) Rake angle
b) Clearance angle
c) Cutting angle
d) Lip angle
The negative rake is usually provide on-
a) High carbon steel tool
b) High speed steel tool
c) Cemented carbide tool
d) All of these
Negative rake are used for-
a) Carbide tools
b) Heavy tools
c) Harder material
d) All of these
The angle made by the face of the tool and plane parallel to the base of cutting tool is called-
a) Rake angle
b) Clearance angle
c) Cutting angle
d) Lip angle
The cutting fluid mostly used for machining alloy steel is-
a) Water
b) Soluble oil
c) Dry
d) Sulphured mineral oil
The factor which affects the tool life is-
a) Tool geometry
b) Cutting speed
c) Feed rate
d) All of these
The tool life is said to be over if-
a) Surface finish is poor
b) There is sudden increase in cutting force and power consumption
c) Overheating and fuming due to heat of friction starts
d) All of the above
A grinding wheel is said to be of if the abrasive grain can be easily dislodged.
a) Soft grade
b) Hard g:rade
c) Medium grade
d) All of these
The Hard grade grinding wheels are denoted by the letters.
A Coarse grained grinding wheel is used to grind-
a) Hard and brittle materials
b) Soft and ductile materials
c) Hard and ductile materials
d) Soft and brittle materials
For fast removal of materials during grinding a grinding wheel is used-
a) Coarse grained
b) Fine grained
c) Medium grained
d) All bf these
The purpose of Jig and fixture is to-
a) Increase production rate
b) Enable employ less skilled operators
c) Increase machining accuracyd) All of these
A good lubricant for thread cutting operation is-
a) Mineral lard oil
b) Water soluble oil
c) Graphite
d) White lead
Tool life is most affected by machine-
a) Cutting speed
b) Tool geometry
c) Feed and depth
d) Microstructure of material being cut
It is possible to correlate tool life with the following property of the metal-
a) Grain size
b) Toughness
c) Hardness
d) Microconsitiuent
Tungsten content in the High speed steel tool cutting tool material is-
d) 0.6%
18-4-1 high speed steel contains following element in the ratio of 18-4-1.
a) Tungsten, Chromium, and vanadium
b) Chromium, vanadium, and Tungsten
c) Vanadium, Tungsten, and Chromium
d) None of these
The characteristics that enable one material to cut another is its relative-
a) Toughness
b) Hardness
c) Resilience
d) Ductility
High speed steel tool material contains carbon-
a) 0.6-1.0%
d) 6-100/0
The angle between the face of tool, and line tangent to the machined surface at the cutting point is known as-
a) Rake angle
b) Cutting angle
c) Clearance angle
d) Lip angle
Chip breakers are provided on cutting tools-
a) For safety of operators
b) To minimize heat generation
c) To permit short segment chips d) To increase tool life
Tool life is said to be over when-
a) Finish of work becomes too rough
b) Cutter looks dull
c) Chips become blue
d) A certain amount of wear or cratering occurs on the flank
The grit, grade and structure of grinding wheels for specific operation are based on-
a) Grinder clearance
b) Spindle size of the grinder
c) Diameter of wheels
d) Speed at which the wheel is to be used
When it is required to run a grinding wheel safely at very high speed. Following bond should be used-
a) Vitrified b) Resinoid and Rubber
c) Shellac d) Silicate
Which of the following is not the angle measuring device?
a) Angle plate
b) Sine bar
c) Angle gauge
d) Screw thread micrometer
Accurate centering of work mounted in an independent chuck can be determined by using
a) Centre gauge
b) Height gauge
c) Dial indicator
d) Micrometer
A sine bar is used to measure-
a) Surface roughness
b) Gear profiles
c) Internal tapers
d) External tapers
The purpose of using borax in brazing is-
a) Dissolve oxides when heating the work
b) Prevent the spelter from melting too quickly
c) Increase fluidity of braze material
d) Accelerate the formation of oxides on the work
29. When brazing is carried out-
a) A joint is made between two parts by molten spelter
b) The edges of the joint melt and run together
c) Spelter forms an alloy with flux
d) Flux acts as a connecting material
30. In soldering the melting point of filter metal is-
c) Below 5200C
31. The composion of soft solder is- d) Above 5200C
a) Below b) Above 4200C
a) Lead-37%, tin b) Lead-67%, tin
c) Lead-70%, tin d) Lead-50%, tin
Contd.-...4/
32. Best coolant and lubrication for bras, copper and bronze is-
a) Soluble oil
b) Water, soluble oil or sulphur based mineral oils
c) Mineral and fatty oils
d) Dry
33. Which of the following operations can be used on Centre lathe?
a) Grinding b) Milling
c) Drilling d) All of these
34. In lathe, form tools are used to produce.
a) Cylindrical surfaces
b) Tapered surfaces
c) The surfaces which are neither cylindrical nor tapered
d) 'l*hrea.ds
35. The following are the function of a jig-
a) Holding b) Locating
c) Guiding d) All of these
36. A fixture does not-
a) Holds the workpiece b) Locate the workpiece
c) Guide the tool d) All of these
37. Jigs are not used in-
a) Drilling b) Reaming
c) -rapping d) Milling
38. The following jig can be used for several different work pieces and operations.
a) eremplate jig b) Multi-station jig
c) Index jig d) Universal jig
39. A fixture is defined as a device which-
a) Hold and locate a workpiece and guide and controls one or more cutting tools
b) Hold and locate a workpiece during an inspection or for manufacturing a operation
c) Is used to check the accuracy of workpiece
d) All of the above
40. Multi thread are used to secure-
a) Low efficiency b) High efficiency
c) High load lifting capacity d) High mechanical advantage
41, External taper can be accurately measured with the help of-
a) Sine bar and slip gauges b) Dividing head
c) Precision balls and height guage d) Combination set
The axial advancement in one rotation of screw pan is known as of the threads.
a) Pitch b) Lead
c) Pitch diameter d) Helix angle
43. The distance from a point on one thread to the corresponding point on the next thread is called.
a) Lead b) Pitch
c) Turn d) Crest
44. The angle included by the flanks of the thread-
a) Angle of thread b) Depth of thread
c) Depth of cut d) Slope of thread
45. Best coolant and lubrication for aluminium.
a) Soluble oil
b) Water, soluble oil or sulphur based mineral oils
c) Mineral and fatty oils or soluable oils
d) Dry
The diameter of a finish turned shaft can best be checked with a-
a) Combination set b) Dial indicator
c) Height gauge d) Micrometer screw gauge
47. The thread micrometer measures-
a) The major diameter of thread b) The minor diameter of thread
c) The effective diameter of thread d) The rod diameter of thread
48. A screw thread is designated as 1" B.S.P. thread, in I inch B.S P. thread what l" indicates?
a) Major diameter of thread h) Minor diameter of thread
c) Pitch diameter of thread d) Hole diameter of Pipe
In a sine bar the standard length is measured from-
a) Edge to edge
b) Between inner circumference of two buttons
c) Between out circumference of two buttons
d) Between the centers of two buttons
50. Work is usually required to be held in a vertical position for layout. For this purpose, lit is
clamped to-
a) Surface plate b) A machine bed
c) An angle plate d) A V block
SEMESTER-III
The angle on which the strength of tool depend is-
a) Rake angle
b) Clearance angle
c) Cutting angle
d) Lip angle
The negative rake is usually provide on-
a) High carbon steel tool
b) High speed steel tool
c) Cemented carbide tool
d) All of these
Negative rake are used for-
a) Carbide tools
b) Heavy tools
c) Harder material
d) All of these
The angle made by the face of the tool and plane parallel to the base of cutting tool is called-
a) Rake angle
b) Clearance angle
c) Cutting angle
d) Lip angle
The cutting fluid mostly used for machining alloy steel is-
a) Water
b) Soluble oil
c) Dry
d) Sulphured mineral oil
The factor which affects the tool life is-
a) Tool geometry
b) Cutting speed
c) Feed rate
d) All of these
The tool life is said to be over if-
a) Surface finish is poor
b) There is sudden increase in cutting force and power consumption
c) Overheating and fuming due to heat of friction starts
d) All of the above
A grinding wheel is said to be of if the abrasive grain can be easily dislodged.
a) Soft grade
b) Hard g:rade
c) Medium grade
d) All of these
The Hard grade grinding wheels are denoted by the letters.
A Coarse grained grinding wheel is used to grind-
a) Hard and brittle materials
b) Soft and ductile materials
c) Hard and ductile materials
d) Soft and brittle materials
For fast removal of materials during grinding a grinding wheel is used-
a) Coarse grained
b) Fine grained
c) Medium grained
d) All bf these
The purpose of Jig and fixture is to-
a) Increase production rate
b) Enable employ less skilled operators
c) Increase machining accuracyd) All of these
A good lubricant for thread cutting operation is-
a) Mineral lard oil
b) Water soluble oil
c) Graphite
d) White lead
Tool life is most affected by machine-
a) Cutting speed
b) Tool geometry
c) Feed and depth
d) Microstructure of material being cut
It is possible to correlate tool life with the following property of the metal-
a) Grain size
b) Toughness
c) Hardness
d) Microconsitiuent
Tungsten content in the High speed steel tool cutting tool material is-
d) 0.6%
18-4-1 high speed steel contains following element in the ratio of 18-4-1.
a) Tungsten, Chromium, and vanadium
b) Chromium, vanadium, and Tungsten
c) Vanadium, Tungsten, and Chromium
d) None of these
The characteristics that enable one material to cut another is its relative-
a) Toughness
b) Hardness
c) Resilience
d) Ductility
High speed steel tool material contains carbon-
a) 0.6-1.0%
d) 6-100/0
The angle between the face of tool, and line tangent to the machined surface at the cutting point is known as-
a) Rake angle
b) Cutting angle
c) Clearance angle
d) Lip angle
Chip breakers are provided on cutting tools-
a) For safety of operators
b) To minimize heat generation
c) To permit short segment chips d) To increase tool life
Tool life is said to be over when-
a) Finish of work becomes too rough
b) Cutter looks dull
c) Chips become blue
d) A certain amount of wear or cratering occurs on the flank
The grit, grade and structure of grinding wheels for specific operation are based on-
a) Grinder clearance
b) Spindle size of the grinder
c) Diameter of wheels
d) Speed at which the wheel is to be used
When it is required to run a grinding wheel safely at very high speed. Following bond should be used-
a) Vitrified b) Resinoid and Rubber
c) Shellac d) Silicate
Which of the following is not the angle measuring device?
a) Angle plate
b) Sine bar
c) Angle gauge
d) Screw thread micrometer
Accurate centering of work mounted in an independent chuck can be determined by using
a) Centre gauge
b) Height gauge
c) Dial indicator
d) Micrometer
A sine bar is used to measure-
a) Surface roughness
b) Gear profiles
c) Internal tapers
d) External tapers
The purpose of using borax in brazing is-
a) Dissolve oxides when heating the work
b) Prevent the spelter from melting too quickly
c) Increase fluidity of braze material
d) Accelerate the formation of oxides on the work
29. When brazing is carried out-
a) A joint is made between two parts by molten spelter
b) The edges of the joint melt and run together
c) Spelter forms an alloy with flux
d) Flux acts as a connecting material
30. In soldering the melting point of filter metal is-
c) Below 5200C
31. The composion of soft solder is- d) Above 5200C
a) Below b) Above 4200C
a) Lead-37%, tin b) Lead-67%, tin
c) Lead-70%, tin d) Lead-50%, tin
Contd.-...4/
32. Best coolant and lubrication for bras, copper and bronze is-
a) Soluble oil
b) Water, soluble oil or sulphur based mineral oils
c) Mineral and fatty oils
d) Dry
33. Which of the following operations can be used on Centre lathe?
a) Grinding b) Milling
c) Drilling d) All of these
34. In lathe, form tools are used to produce.
a) Cylindrical surfaces
b) Tapered surfaces
c) The surfaces which are neither cylindrical nor tapered
d) 'l*hrea.ds
35. The following are the function of a jig-
a) Holding b) Locating
c) Guiding d) All of these
36. A fixture does not-
a) Holds the workpiece b) Locate the workpiece
c) Guide the tool d) All of these
37. Jigs are not used in-
a) Drilling b) Reaming
c) -rapping d) Milling
38. The following jig can be used for several different work pieces and operations.
a) eremplate jig b) Multi-station jig
c) Index jig d) Universal jig
39. A fixture is defined as a device which-
a) Hold and locate a workpiece and guide and controls one or more cutting tools
b) Hold and locate a workpiece during an inspection or for manufacturing a operation
c) Is used to check the accuracy of workpiece
d) All of the above
40. Multi thread are used to secure-
a) Low efficiency b) High efficiency
c) High load lifting capacity d) High mechanical advantage
41, External taper can be accurately measured with the help of-
a) Sine bar and slip gauges b) Dividing head
c) Precision balls and height guage d) Combination set
The axial advancement in one rotation of screw pan is known as of the threads.
a) Pitch b) Lead
c) Pitch diameter d) Helix angle
43. The distance from a point on one thread to the corresponding point on the next thread is called.
a) Lead b) Pitch
c) Turn d) Crest
44. The angle included by the flanks of the thread-
a) Angle of thread b) Depth of thread
c) Depth of cut d) Slope of thread
45. Best coolant and lubrication for aluminium.
a) Soluble oil
b) Water, soluble oil or sulphur based mineral oils
c) Mineral and fatty oils or soluable oils
d) Dry
The diameter of a finish turned shaft can best be checked with a-
a) Combination set b) Dial indicator
c) Height gauge d) Micrometer screw gauge
47. The thread micrometer measures-
a) The major diameter of thread b) The minor diameter of thread
c) The effective diameter of thread d) The rod diameter of thread
48. A screw thread is designated as 1" B.S.P. thread, in I inch B.S P. thread what l" indicates?
a) Major diameter of thread h) Minor diameter of thread
c) Pitch diameter of thread d) Hole diameter of Pipe
In a sine bar the standard length is measured from-
a) Edge to edge
b) Between inner circumference of two buttons
c) Between out circumference of two buttons
d) Between the centers of two buttons
50. Work is usually required to be held in a vertical position for layout. For this purpose, lit is
clamped to-
a) Surface plate b) A machine bed
c) An angle plate d) A V block
No comments:
Post a Comment